Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands Uživatelský manuál Strana 22
- Strana / 142
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2.1 Preparing for Operation
2-5
2
Operation Sequence
Setting the Station Address
The following table lists the possible settings of the DIP switches (SW1 and SW2) that can be combined to
form a station address.
The factory setting for the station address is 41H (Bit 3 of SW2 = OFF, Bit 1 of SW1 = ON, Bit 2 of SW1 =
OFF, Bit 3 of SW1 = OFF, Bit 4 of SW1 = OFF).
Setting
Station Address
Bit 3 of SW2 Bit 1 of SW1 Bit 2 of SW1 Bit 3 of SW1 Bit 4 of SW1
OFF OFF OFF OFF OFF Disabled
OFF ON OFF OFF OFF 41H
OFF OFF ON OFF OFF 42H
OFF ON ON OFF OFF 43H
OFF OFF OFF ON OFF 44H
OFF ON OFF ON OFF 45H
OFF OFF ON ON OFF 46H
OFFONONONOFF 47H
OFF OFF OFF OFF ON 48H
OFF ON OFF OFF ON 49H
OFF OFF ON OFF ON 4AH
OFF ON ON OFF ON 4BH
OFF OFF OFF ON ON 4CH
OFF ON OFF ON ON 4DH
OFF OFF ON ON ON 4EH
OFFONONONON 4FH
ON OFF OFF OFF OFF 50H
ON ON OFF OFF OFF 51H
ON OFF ON OFF OFF 52H
ON ON ON OFF OFF 53H
ON OFF OFF ON OFF 54H
ON ON OFF ON OFF 55H
ON OFF ON ON OFF 56H
ON ON ON ON OFF 57H
ON OFF OFF OFF ON 58H
ON ON OFF OFF ON 59H
ON OFF ON OFF ON 5AH
ON ON ON OFF ON 5BH
ON OFF OFF ON ON 5CH
ON ON OFF ON ON 5DH
ON OFF ON ON ON 5EH
ON ON ON ON ON 5FH
Turn the power OFF and then ON again to validate the new settings.
- Σ-V Series 1
- About this Manual 3
- Warranty 4
- (3) Suitability for Use 5
- (4) Specifications Change 5
- Contents 6
- 1.1.1 Layers 10
- 1.1.2 Frame Structure 10
- MECHATROLINK-II Commands 11
- 1.1.4 Terminology 12
- 1 MECHATROLINK-II Commands 14
- 1.4 Data Order 17
- Operation Sequence 18
- 2.1 Preparing for Operation 19
- Setting the Station Address 20
- 2 Operation Sequence 21
- -J11) are Used 23
- (1) Operation Procedure 25
- Controller 26
- 2.3.1 Setup Sequence 27
- POS: Reference position 31
- 3.2.1 No Operation (NOP: 00H) 34
- (4) Details WDT and RWDT 36
- (1) DISCONNECT Command (0FH) 37
- (1) CONNECT Command (0EH) 38
- (2) Details of COM_MOD 39
- (1) SYNC_SET Command (0DH) 40
- (1) ID_RD Command (03H) 41
- (2) Device ID Specifications 42
- ID_RD aSGDV2R9E11A00 43
- ID_RD bSGDV131J11A00 44
- (1) PRM_WR Command (02H) 45
- (1) PPRM_WR Command (1CH) 46
- (1) CONFIG Command (04H) 47
- (1) SENS_ON Command (23H) 48
- • Applicable Commands: 50
- (1) SV_ON Command (31H) 51
- 3.2 Commands Details 52
- (1) SENS_OFF Command (24H) 54
- (1) SV_OFF Command (32H) 55
- (1) PRM_RD Command (01H) 56
- (1) SMON Command (30H) 57
- (1) ALM_RD Command (05H) 58
- (2) ALM_RD_MOD Specifications 59
- (1) ALM_CLR Command (06H) 60
- (1) POS_SET Command (20H) 61
- (2) PS_SUBCMD Specifications 61
- (1) ADJ Command (3EH) 62
- C01EH reference value 65
- C021H reference value 65
- Motion Commands for Operation 66
- 4.1 Motion Commands List 67
- 4.2.1 Stop Motion (HOLD: 25H) 68
- (2) Related Parameters 69
- (1) LTMOD_ON Command (28H) 70
- (2) Normal Latch Mode 70
- (3) Continuous Latch Mode 71
- (4) LT_SGNL Specifications 72
- (5) Related Parameters 72
- (1) LTMOD_OFF Command (29H) 73
- (1) INTERPOLATE Command (34H) 74
- (1) POSING Command (35H) 76
- (1) FEED Command (36H) 78
- (1) LATCH Command (38H) 80
- (1) EX_POSING Command (39H) 82
- (2) Operation 83
- (3) Related Parameters 83
- 4.2.9 Homing (ZRET: 3AH) 84
- (1) VELCTRL Command (3CH) 86
- Before soft-start 87
- After soft-start 87
- Max. motor speed 87
- Pn305 Pn306 87
- (1) TRQCTRL (3DH) 88
- (2) Speed Limit Option 1 89
- (3) Speed Limit Option 2 89
- 5.2.1 Electronic Gear Setting 93
- Position 94
- (2) Position Reference Filter 96
- 5.2.3 Motion Sequence Setting 99
- 5.2.4 Command Data Options 100
- 5 Command Related Parameters 101
- 5.2.4 Command Data Options 101
- (4) OPTION Field Allocation 102
- (1) Latching Allowable Area 104
- (2) Continuous Latch Function 104
- Command Related Parameters 106
- NEAR Signal Width Setting 111
- (3) Option Monitor Setting 113
- MECHATROLINK-II Subcommands 114
- 6.2.1 No Operation (NOP: 00H) 115
- Data Field 120
- 7.1 Main Command Data Field 121
- (1) Applicable Commands 123
- (2) Setting Method 125
- Applicable Commands 126
- 7.1.6 LT_SGNL Specifications 128
- 7.2 Substatus Data Field 129
- Communications or Commands 130
- 8.1 List of Alarms 131
- 8.1 List of Alarms 132
- 8.2 List of Warnings 133
- 8.2 List of Warnings 134
- Appendix 136
- A Brake Control Commands 137
- • Sub-control (SUBCTRL) 139
- Select Motion (MOTION) 140
- Select Latch Signal (L_SGN) 140
- • Sequence Signals: SQ_CMD 140
- Revision History 141
Související produkty a manuály pro Zařízení Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands
(460 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce