Yaskawa VS-616G5 Series Revision F Programming Manual Uživatelský manuál stáhnout pdf (Strana 76)

V/f V/f w/PG

Open Loop

Vector

Flux

Vector

76 VS-616G5 Programming Manual

Section H: Control Circuit Terminals

H1 Digital Inputs

The setting of parameter F9-06 selects the stopping method when an BUS fault is detected.

A BUS fault may occur when using the SI-B or the CP-916 communication options. The fault will

occur after initial communication has been established then the connection is lost. The following fault

code will be displayed: “BUS SI-B Com Err”.

H Control Circuit Terminal Parameters

H1 Digital Inputs

The VS-616G5 has six multi-function contact inputs for the set-up of numerous functions, including

multi-step speed operation, PID, speed search, speed/torque control selection, and many other. This

section includes descriptions of these functions.

The following table lists the function selections for the multi-function contact inputs (terminals 4 to 8),

and indicates the control modes during which each function can be enabled.

F9-06 Bus Fault Select Bus Fault Sel

A A A A

Setting Description

0 Ramp to Stop - Ramp to stop according to C1-02 set value.

1 Coast to stop.

2 Fast-Stop - Ramp to stop according to C1-09 set value.

3 Alarm Only - Alarm flashes, operation continues.

H1-01 Multi-function Input Terminal 3 Selection Terminal 3 Sel

B B B B

H1-02 Multi-function Input Terminal 4 Selection Terminal 4 Sel

B B B B

H1-03 Multi-function Input Terminal 5 Selection Terminal 5 Sel

B B B B

H1-04 Multi-function Input Terminal 6 Selection Terminal 6 Sel

B B B B

H1-05 Multi-function Input Terminal 7 Selection Terminal 7 Sel

B B B B

H1-06 Multi-function Input Terminal 8 Selection Terminal 8 Sel

B B B B

H1-01

to 6

Setting

Function

Control Method (A1-02)

Reference

PageV/f V/f w/ PG

Open Loop

Vector

Flux Vector

0 3-Wire Control √ √ √ √

1 Local/Remote Selection √ √ √ √

2 Option/Inverter Selection √ √ √ √

3 Multi-Step Ref. 1 (factory default, H1-03) √ √ √ √

4 Multi-Step Ref. 2 (factory default, H1-04) √ √ √ √

5 Multi-Step Reference 3 √ √ √ √

6 Jog Frequency Ref. (factory default, H1-05) √ √ √ √

7 Multi-Accel/Decel 1 √ √ √ √

8 Ext. Baseblock N.O. (factory default, H1-06) √ √ √ √

9 External Baseblock N.C. √ √ √ √

A Accel/Decel Ramp Hold √ √ √ √

B OH2 Alarm Signal √ √ √ √

C Terminal 16 Enable √ √ √ √

D V/f Mode Selection − √ − −

E ASR Integral Reset − √ − √

10 MOP Increase √ √ √ √

11 MOP Decrease √ √ √ √

1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 161 162

Komentáře k této Příručce

Žádné komentáře

Yaskawa VS-616G5 Series Revision F Programming Manual Uživatelský manuál Strana 76

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Yaskawa VS-616G5 Series Revision F Programming Manual